Cold Room Air Curtains and Dock Door Seals: Cutting Infiltration Heat at the Doorway

A cold room is usually judged by its panels and its condensing unit, because those are the expensive items on the quotation. But the largest uncontrolled heat load in most working cold stores enters through a rectangle of air that nobody priced: the doorway.
Panels leak heat slowly and predictably; a door leaks it quickly and unpredictably. A 2 m × 2.2 m opening on a −18 °C freezer, standing open at 30 °C ambient, pulls in heat at a rate that can equal the entire capacity of a mid-size condensing unit — and it does so every time a forklift passes. The plant then runs longer, the evaporator ices faster, defrost cycles multiply, and the electricity bill arrives with no obvious explanation.
This article covers the four devices that control doorway losses, how to size them by door height and duty rather than by catalogue page, where they are routinely misapplied, and what data a supplier needs before quoting. It applies to chiller rooms, freezer rooms, blast freezers given they are opened between batches, and to refrigerated dock houses.
⚠️ All U-values, infiltration rates, capacities and cost indices below are industry-typical reference figures for planning discussion only. Final values must be calculated for your actual room geometry, climate, product, traffic pattern and electricity tariff. Every price must be replaced with your actual quotation.
The doorway is a capacity problem, not a comfort problem
Infiltration is not a small correction to the cooling load. Treat it as a design load with its own calculation, separate from transmission through panels and from product load. Three variables dominate:
- Opening area and height. Heat and moisture enter through the open face. Door height matters more than width, because the buoyancy-driven exchange is driven by the height of the column of cold air falling out of the room.
- Temperature difference and ambient humidity. A freezer in a humid climate is a worse doorway problem than a chiller in a dry one, because moisture arrives with the air and leaves as frost on the coil, which then has to be melted off at the plant's expense.
- Open time. Not the number of openings, but total seconds per hour that the opening is actually clear. A door that is open 30 seconds for a pallet truck, 40 times an hour, is open for 20 minutes of every hour.
The table below gives an order of magnitude for a fully open doorway, still air, 30 °C and 60 % RH ambient, no doorway protection fitted. Use it to decide whether the doorway deserves attention on your project — not to size equipment.
| Door opening (W × H) | Chiller at +4 °C | Chiller at 0 °C | Freezer at −18 °C | Freezer at −25 °C |
|---|---|---|---|---|
| 1.5 m × 2.2 m | ≈ 5 kW | ≈ 6 kW | ≈ 11 kW | ≈ 13 kW |
| 2.0 m × 2.2 m | ≈ 7 kW | ≈ 9 kW | ≈ 16 kW | ≈ 20 kW |
| 2.5 m × 3.0 m | ≈ 12 kW | ≈ 15 kW | ≈ 28 kW | ≈ 34 kW |
| 3.0 m × 3.5 m (dock) | ≈ 17 kW | ≈ 21 kW | ≈ 38 kW | ≈ 46 kW |
On a small chiller room the doorway load is comparable to everything else, which is why a small walk-in with a badly fitted strip curtain never holds temperature on a busy day. On a freezer room or dock door it can exceed the installed plant capacity outright, and the fault is then reported as "the unit is too small".
The four devices, and what each one actually does
Doorway protection is a system, not a single product: the right combination depends on how often the opening is used and whether a vehicle docks against it.
| Device | Typical reduction in infiltration | Best suited to | Cost index | Fails when |
|---|---|---|---|---|
| Strip curtain (PVC) | 40–70 % | Pedestrian and pallet doorways opened frequently, chiller and freezer, no vehicle docking | 1.0 (baseline) | Strips too short, overlap under 30 %, rigid PVC used in a freezer and cracked at −25 °C |
| Air curtain, ambient discharge | 60–80 % | Doors up to about 3.5 m high with heavy traffic, chilled rooms, retail and packing areas | 2–3 | Mounted outside the envelope; room under negative pressure; nozzle velocity set for summer and left there |
| Air curtain, cooled / recirculated | 60–80 % | Freezer doorways and dock doors where ambient discharge would condense or freeze | 3–4 | No drain for condensate; coil never cleaned; used where an airlock was the cheaper answer |
| Dock seal or shelter plus rapid roll door | 80–95 % while a trailer is docked | Loading bays, distribution cold stores, any door served by vehicles | 2–5 | Seal fitted to the drawing instead of the fleet; gap left at the top of the trailer; door left open between trailers |
| Airlock / vestibule with two interlocked doors | 85–95 % | High-traffic freezer rooms, pharmaceutical and GSP/GDP rooms, any room where product cannot see ambient | 4–6 | Both doors open at once because the interlock was value-engineered out |
⚠️ The cost index is relative to a strip curtain on the same opening, supplied and installed. It is not a price. Replace it with your actual quotation.
The cheapest device delivers most of the benefit on a pedestrian doorway; the most expensive is the only one that guarantees separation. Between them sits the air curtain — the most frequently misapplied product in the whole package.
Engineering tip: Air curtains are not "fans over the door". A unit selected by door width alone will underperform on a tall opening, because the discharge velocity has to reach the floor with enough momentum left to resist the cold-air column falling out of the room. As a starting reference, expect a nozzle discharge velocity around 8–12 m/s for a door up to 3 m high, rising for taller openings, and verify the figure against at least 70 % of it measured at floor level. Ask the supplier for the velocity at the floor, not at the nozzle.
Sizing by door height, not by door width
Catalogue selection tables usually start with door width, because that determines the unit length. But effectiveness is governed by height. A 3 m wide, 2 m high door is easy; a 2 m wide, 4 m high door is hard, and no amount of extra nozzle length fixes it.
| Door clear height | Practical options | Notes for specification |
|---|---|---|
| Up to 2.5 m | Strip curtain, or ambient air curtain | Single-nozzle unit is adequate; check strip overlap at 30–50 % |
| 2.5–3.5 m | Ambient air curtain sized on velocity, or airlock | Above about 3 m, require the supplier to state discharge velocity and floor-level velocity in writing |
| 3.5–4.5 m | Cooled air curtain, airlock, or dock seal with rapid door | Ambient discharge in a freezer at this height will condense and drip; specify a drain |
| Above 4.5 m | Airlock or full dock enclosure | Single air curtain is not a credible solution at this height; do not accept one on price |
For freezer rooms the choice is narrower than the catalogue suggests. An ambient air curtain blowing 30 °C air across a −25 °C opening creates a condensate stream, and in cold climates it can freeze the floor at the threshold into a ridge of ice that forklifts then break up. Either specify a cooled unit with a condensate drain and heater, or use an airlock.
Dock seals: measure the fleet, not the drawing
Loading bay doors are where doorway losses are largest and where specification is most often skipped. The door itself is only half the problem; the interface with the trailer is the other half.
Three measurements decide whether a dock seal will work:
- Trailer bed height range across the actual fleet, not the nominal figure. A seal designed around one trailer height will gap on the tallest and crush on the lowest.
- Dock opening height versus trailer height. A gap along the top of the trailer is the most common failure, and it is invisible from inside because the seal looks closed.
- Bumper projection and leveller position. If the trailer stands off the bumpers, the seal compresses unevenly and opens at the corners.
| Dock arrangement | Seal type | Infiltration control | Watch out for |
|---|---|---|---|
| Single regular fleet, fixed bed height | Sponge or inflatable dock seal | Good | Inflatable seals need an air supply and a maintenance routine; a puncture goes unnoticed |
| Mixed fleet, varying heights | Dock shelter with top and side curtains | Moderate — covers the gap, not the seal | Shelter does not seal; it only screens. Pair with a rapid roll door kept closed between vehicles |
| Trailer parked for long periods (live load) | Seal plus vehicle restraint | Good | Without a restraint, creep between trailer and dock reopens the gap |
| No vehicle, pallet traffic only | Strip curtain or airlock | Good | Strip curtain in a freezer needs low-temperature PVC, not standard PVC |
Engineering tip: A 100 mm gap along the top of a docked trailer on a −18 °C room leaks more heat than a 2 m² pedestrian doorway standing open, and it leaks continuously for the entire loading cycle rather than for 30 seconds. Before buying a larger condensing unit to "fix" a warm dock, put a hand at the top corners of the seal on a cold day. Gaps show up as a draught and as a line of condensation.
Pressure balance: the failure nobody quotes for
An air curtain is a barrier of moving air. It only works if the room is roughly neutral to ambient. In practice, cold rooms are rarely neutral:
- Evaporator fans and air-cooler ductwork create local suction near the coil, and if the room has no relief path the makeup air arrives through the doorway.
- Defrost cycles transiently change room pressure, and a room with a tight envelope and no pressure relief valve will pull air in through the door seal or push it out into the wall joints.
- An airlock with no relief between its two doors behaves as a piston each time a door closes.
The fix is unglamorous: provide a pressure relief path, keep the air curtain inside the insulated envelope so it draws room-side air, and avoid putting the unit above a door that opens directly to the outside of the building where wind pressure will dominate the curtain. On exposed sites, wind at the doorway is often the real reason a correctly sized curtain "does not work".
Engineering tip: Commission the doorway, do not just install it. An anemometer traverse across the opening at 0.5 m intervals, at nozzle height and at floor level, will show a weak section within minutes. A smoke pencil around a docked seal shows gaps that a visual inspection misses. Repeat the same measurements after the first month of operation, once panels have settled and doors have been adjusted — this is also the point at which most strip curtains have already lost a strip or two.
What to send a supplier before asking for a price
Most doorway products are quoted from incomplete data, producing a unit that is the wrong size or a seal that fits the drawing. The data sheet below is what a supplier needs to quote properly.
| Item | What to provide | Why it matters |
|---|---|---|
| Opening dimensions | Clear width and clear height, measured, plus threshold detail | Height drives air curtain selection more than width |
| Room temperature and tolerance | Design temperature, defrost method, expected excursion | Determines ambient versus cooled discharge, and PVC grade |
| Traffic pattern | Openings per hour, seconds per opening, peak hour, vehicle or pallet | Converts into open time per hour, the real design variable |
| Vehicle data (docks only) | Fleet bed height range, trailer widths, bumper type, leveller model | Seal selection is a fleet decision, not a door decision |
| Environment | Ambient design temperature and RH, wind exposure, indoor or outdoor face | Humidity decides condensate and frost risk; wind defeats curtains |
| Pressure and relief | Existing relief path, airlock presence, adjacent rooms | A curtain cannot hold against sustained negative pressure |
| Electrical supply | Voltage, frequency, phase, position of isolator | Air curtains and heated seals are electrical items; heaters need their own circuit |
| Controls interface | Interlock with door, BMS or monitoring system | Interlocks are the cheapest way to guarantee doors are not left open |
Where buyers most often overspend, and where they most often underspend
Overspending is common on dock hardware for a lightly used bay, and on air curtains where a strip curtain would have done. Underspending is in the same three places:
- No airlock on a high-traffic freezer room. Retrofitting an airlock later costs more than including it, and it is the only device that guarantees separation independent of operator behaviour.
- Standard PVC strip in a freezer. It goes brittle, cracks, and the doorway is then effectively open. Specify low-temperature PVC and check the grade in writing.
- No commissioning. An air curtain installed at the wrong angle, or a dock seal fitted 50 mm high, performs like no device at all, and the money is already spent.
Doorway protection also interacts with the rest of the room: if the cooling load already includes infiltration, a curtain is simply the cheaper way to meet it than buying a larger plant.
Shandong Boruite Refrigeration Equipment Co., Ltd. manufactures PU insulation panels and cold room doors in its own workshop in Boxing County, Binzhou, Shandong, China, and supplies design, equipment, installation and after-sales support for cold room projects. Doorway protection is specified together with the door package, because the door, the frame, the seal and the air curtain are one assembly and are best sized together.
For a project quotation, send the data sheet above with your room dimensions, temperature requirement and traffic pattern to 3107900547@qq.com or call +86 15898896999. Door height, fleet bed height range and openings per hour are the three figures that change the recommendation most; with those, the doorway package can be priced without a site visit.
Send us the product, storage volume, target temperature and site conditions — our engineers will come back with a preliminary scheme and budget range within 24 hours.
Email us 15898896999