Cold Room Cooling Load Calculation: How to Check Your Supplier's kW Numbers

Almost every cold room quotation contains one number that decides whether the room will hold temperature in August: the refrigeration capacity, usually written as something like "2 × 5 HP, 11.5 kW". Very few quotations show how that number was reached. When the room later fails to pull down, or runs continuously at 95% duty, the argument that follows is almost always about equipment quality — when the real problem is that the load was never calculated, only estimated from a rule of thumb such as "1 HP per 10 cubic metres".
This article shows the calculation the way a refrigeration engineer does it, with a worked example you can copy, and then explains the derating that makes a nominal kW rating nearly meaningless unless you know the evaporating temperature it was measured at.
Why the quoted kW is usually not the load
A compressor's capacity is not a fixed property. It depends on the condensing temperature (how hot the ambient is) and the evaporating temperature (how cold the coil runs). The same condensing unit that delivers 11 kW at −10 °C evaporating will typically deliver 6–7 kW at −25 °C. Freezer rooms need the coil well below the room temperature to transfer heat, so a freezer is always quoted at a lower evaporating temperature than a chiller of the same nominal size.
That single fact explains most "the equipment is too small" complaints: the buyer compared two quotations by their nominal kW, but one was rated at −10 °C and the other at −25 °C. The numbers were never comparable.
The five load components
A cooling load is the sum of everything that brings heat into the room. Engineers normally split it into five groups, and each group behaves differently through the year.
| Component | What it covers | Typical share in a small freezer |
|---|---|---|
| Transmission | Heat through panels, ceiling and floor | 10–20% |
| Product | Heat removed from goods entering above storage temperature | 40–60% |
| Infiltration | Warm air entering through doors, plus air leakage | 10–20% |
| Internal | Evaporator fans, lights, defrost heaters, people | 10–15% |
| Respiration | Heat released by living produce (fresh rooms only) | 0–25% |
For a chiller storing packaged goods, transmission and infiltration dominate. For a freezer with a high daily intake, product load dominates and the equipment is effectively sized around the pull-down peak rather than the holding state. For a fresh produce room, respiration can be larger than the panel gain and must be calculated from the commodity, not guessed.
A worked example: 100 m³ freezer at −18 °C
Take a 5 × 5 × 4 m freezer room, 150 mm PU panels, ambient 32 °C, intake 2 tonnes per day of packed goods arriving at +25 °C. Interior surface area is 130 m² (walls 80, ceiling 25, floor 25).
1. Transmission. With a panel U-value around 0.15 W/m²K and a 50 K difference between ambient and room, the gain is 0.15 × 130 × 50 ≈ 975 W, so about 1.0 kW. The floor is normally calculated against ground temperature rather than ambient, which reduces this slightly; using ambient is conservative and appropriate for a first pass.
2. Product load. Cooling 1 kg of goods from +25 °C to −18 °C takes roughly 380 kJ: about 100 kJ to reach freezing, 250 kJ of latent heat, and 30 kJ to sub-cool to storage temperature. For 2,000 kg per day, that is 760,000 kJ over 86,400 seconds, or 8.8 kW averaged across the day. Note the word averaged — if all the goods arrive in a four-hour window, the instantaneous load is roughly six times higher, which is why intake pattern matters as much as daily tonnage.
3. Infiltration. For a small freezer with 20–30 door openings a day, an allowance of 1.0–1.5 kW is realistic. Strip curtains, air curtains and fast-acting doors reduce it; a wide door left open during loading can double it.
4. Internal gains. Evaporator fans (0.5–0.7 kW), lights (0.1 kW), defrost heaters averaged over the cycle (0.4–0.6 kW) and two people working inside (0.2 kW) add up to about 1.3–1.5 kW. These are small individually and easy to forget collectively.
5. Respiration. Not applicable to frozen packaged goods. It becomes significant for fresh fruit and vegetables, where the commodity's heat of respiration at storage temperature must be added — for leafy vegetables it can reach 20–40 W per tonne, and considerably more in the first hours after harvest.
Adding the four applicable components gives 1.0 + 8.8 + 1.2 + 1.4 ≈ 12.4 kW at design conditions. A 10% margin for door openings during peak intake and panel ageing brings the required capacity to about 13.6 kW — at an evaporating temperature of roughly −25 °C.
The derating table that decides whether the room works
This is the step most quotations skip. Ask for the capacity at your actual evaporating temperature, not at a nominal rating.
| Evaporating temperature | Relative capacity of the same unit | What it means for the example |
|---|---|---|
| −10 °C | 100% (nominal) | A 13 kW unit here is not a 13 kW freezer unit |
| −20 °C | 75–80% | 13 kW nominal → about 10 kW |
| −25 °C | 60–65% | 13 kW nominal → about 8 kW — short of the 13.6 kW required |
| −30 °C | 50–55% | Blast freezing duty, needs a different selection entirely |
Read the table with the worked example and the failure mode becomes obvious: a supplier who selects "13 kW" from a catalogue page rated at −10 °C has effectively installed an 8 kW freezer. The room will hold temperature on a cool day with light stock and fail exactly when it is full in summer. Nothing is broken; the equipment was never the right size for the duty.
Engineering tip: Always ask for the capacity at the design evaporating temperature and the design condensing temperature (for example "9.2 kW at −25/−40 °C"), plus the ambient the condensing temperature corresponds to. A quotation that lists only horsepower or only a single kW figure cannot be verified.
Engineering tip: Size the evaporator for a smaller temperature difference than the compressor can theoretically accept. A 6–8 K difference between room and evaporating temperature keeps humidity stable and avoids the coil icing every few hours; pushing to 10–12 K to save coil cost trades capital expenditure for defrost cycles and product weight loss.
The part nobody quotes: latent load and humidity
The calculation above treats the load as sensible heat — energy that changes temperature. In chillers there is a second component: latent heat, the energy released when moisture in the incoming air condenses on the evaporator coil. It does not lower the product temperature at all, but the compressor still has to remove it, and in a humid climate it can account for a fifth of the total duty.
Latent load is why two rooms with identical dimensions and identical product can need different equipment. A chiller in a coastal city at 85% relative humidity carries far more moisture into the room with every door opening than the same room inland at 45%. It is also why an oversized evaporator fan can make things worse: a larger temperature difference across the coil pulls more moisture out of the air, which builds frost faster and forces more frequent defrost — heat that then has to be removed again.
For frozen storage, latent load is small in the holding state because the incoming air is dry, but it becomes visible as frost on the coil and on the door frame. For fresh produce and meat chillers, ask the supplier whether the quoted capacity includes latent load at your design humidity, or only sensible heat. The difference is not academic; it decides whether the room holds 0 to +4 °C during a rainy week.
Three load mistakes that show up after commissioning
Using daily tonnage as an hourly rate. A room designed for 2 tonnes a day is not designed for 2 tonnes in an hour. If intake is concentrated, the load must be calculated on the peak hour, or the room needs a separate pre-cooling step. This is the most common cause of "it works in winter and fails in summer".
Forgetting the defrost energy. Electric defrost adds heat directly into the room. On a freezer with four defrosts a day at 30 minutes each, that is two hours of heater energy the refrigeration system must remove again. It is part of the load, not a control detail.
Ignoring door discipline. The infiltration allowance assumes doors are closed when not in use. A docking area with a permanently open door, or staff propping the door for convenience, can add several kW that no calculation anticipated. Physical measures — strip curtains, dock seals, alarm-on-open — are cheaper than the extra compressor capacity.
Five questions to ask before accepting a capacity figure
- What evaporating and condensing temperature does this kW rating correspond to?
- What intake temperature and how many tonnes per day did you assume?
- How many air changes or door openings per day are included for infiltration?
- Is the defrost heat included in the load?
- What is the running duty cycle at design ambient — 60%, 80%, or continuous?
A supplier who can answer all five has done the calculation. One who answers only the first two has probably copied a similar project.
Where the load connects to the rest of the design
The load figure feeds three other decisions: the condensing unit selection (capacity at the right evaporating temperature, covered in our guide to condensing unit sizing for cold rooms), the panel thickness that determines the transmission share, and the annual electricity cost, which is roughly the load multiplied by running hours and the local tariff — the method is set out in cold room energy consumption and running cost. A room that is oversized by 30% to be "safe" pays for that margin every month for ten years.
Engineering tip: Keep the load calculation with the project file, including the assumptions. When the business later adds a product line, changes intake temperature or extends the room, the original sheet tells you instantly whether the existing equipment has headroom — instead of starting the argument from scratch.
What to send us for a capacity check
If you already have a quotation and want a second opinion, send the room dimensions, panel thickness, product type and daily intake, the intake temperature and the target room temperature, plus the ambient design condition for your site. We will return the load breakdown by component and the capacity the equipment needs to deliver at the correct evaporating temperature. That comparison usually takes less time than the negotiation it prevents.
Send us the product, storage volume, target temperature and site conditions — our engineers will come back with a preliminary scheme and budget range within 24 hours.
Email us 15898896999